Skip to content
Merged
Show file tree
Hide file tree
Changes from all commits
Commits
File filter

Filter by extension

Filter by extension

Conversations
Failed to load comments.
Loading
Jump to
Jump to file
Failed to load files.
Loading
Diff view
Diff view
60 changes: 60 additions & 0 deletions Drivers/v4net.device/3.0-beta/AmigaOS/Devs/NetInterfaces/V4Net
Original file line number Diff line number Diff line change
@@ -0,0 +1,60 @@
# $VER: V4Net 1.0 (23.01.2020)
#
# Configuration for the Vampire V4 internal Ethernet

# The device name is mandatory
device=v4net.device
mtu=1492

# If not provided, unit number 0 will be used. You may
# have to change this if there are multiple cards of the
# same type installed in your machine, or if your network
# hardware supports several independent connections
#unit=0

# You must either pick a fixed (static) IPv4 address and
# a corresponding subnet mask, or request DHCP (dynamic)
# network address configuration.
# You can combine address/netmask/dhcp, which has the effect
# of asking the DHCP server to assign the requested IPv4
# address and subnet mask to this interface, if possible.
#address=192.168.10.10
#netmask=255.255.255.0
configure=dhcp

# If no DHCP server is present in your network, you can
# use automatic interface IPv4 address assignment through
# the ZeroConf protocol. Note that this will not set up
# default route and DNS servers for you, only the interface
# address is configured.
#configure=auto

# This variant of automatic IPv4 address assignment should
# be used in a wireless network instead of 'configure=auto'
#configure=fastauto

# You can enable diagnostic messages which can be helpful in
# tracking down configuration errors.
#debug=yes

# You can choose how much memory will be used when handling
# incoming and outgoing network traffic for this device.
# The default is to reserve 32 buffers of 1500 byte each, both
# inbound and outbound traffic. Larger values may provide
# better performance.
iprequests=48
#writerequests=32

# For diagnostic and monitoring purposes it can be helpful to
# capture network traffic that flows through this interface.
# To enable this option, select one of filter=local,
# filter=ipandarp or filter=everything
#filter=local
#filter=ipandarp
#filter=everything

# This option disables a workaround required for the Ariadne
# network hardware, which, if enabled, would otherwise cause
# the interface setup procedure to take longer than really
# necessary.
requiresinitdelay=no
Binary file not shown.
Binary file not shown.
60 changes: 60 additions & 0 deletions Drivers/v4net.device/3.0-beta/ApolloOS/Devs/NetInterfaces/V4Net
Original file line number Diff line number Diff line change
@@ -0,0 +1,60 @@
# $VER: V4Net 1.0 (23.01.2020)
#
# Configuration for the Vampire V4 internal Ethernet

# The device name is mandatory
device=v4net.device
mtu=1492

# If not provided, unit number 0 will be used. You may
# have to change this if there are multiple cards of the
# same type installed in your machine, or if your network
# hardware supports several independent connections
#unit=0

# You must either pick a fixed (static) IPv4 address and
# a corresponding subnet mask, or request DHCP (dynamic)
# network address configuration.
# You can combine address/netmask/dhcp, which has the effect
# of asking the DHCP server to assign the requested IPv4
# address and subnet mask to this interface, if possible.
#address=192.168.10.10
#netmask=255.255.255.0
configure=dhcp

# If no DHCP server is present in your network, you can
# use automatic interface IPv4 address assignment through
# the ZeroConf protocol. Note that this will not set up
# default route and DNS servers for you, only the interface
# address is configured.
#configure=auto

# This variant of automatic IPv4 address assignment should
# be used in a wireless network instead of 'configure=auto'
#configure=fastauto

# You can enable diagnostic messages which can be helpful in
# tracking down configuration errors.
#debug=yes

# You can choose how much memory will be used when handling
# incoming and outgoing network traffic for this device.
# The default is to reserve 32 buffers of 1500 byte each, both
# inbound and outbound traffic. Larger values may provide
# better performance.
iprequests=48
#writerequests=32

# For diagnostic and monitoring purposes it can be helpful to
# capture network traffic that flows through this interface.
# To enable this option, select one of filter=local,
# filter=ipandarp or filter=everything
#filter=local
#filter=ipandarp
#filter=everything

# This option disables a workaround required for the Ariadne
# network hardware, which, if enabled, would otherwise cause
# the interface setup procedure to take longer than really
# necessary.
requiresinitdelay=no
Binary file not shown.
Binary file not shown.
Loading